1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

91 YJ Won't start

Discussion in 'Wrangler YJ (1986-1995)' started by vlkski, Jan 17, 2017.

Page 2 of 2
  1. Feb 1, 2017 at 3:22 PM
    #21
    OFFGRID

    #21
    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    How much lift is your body lift. I tend to avoid them, but I have used a 1" body lift in the past, and last I heard that is the max body lift allowed in Utah by law. Here in TX they allow a 3 in lift. I like the standard Crown rubber body mount kit $95 at Morris4x4. http://www.morris4x4center.com/jeep-body-parts/yj-bodyparts.htm
     
    OFFGRID, Feb 1, 2017
    #21
  2. Feb 1, 2017 at 3:41 PM
    #22
    vlkski

    #22
    vlkski [OP] Member

    Joined:
    Jan 13, 2017
    Member:
    #792
    Messages:
    16
    Gender:
    Male
    First Name:
    Vic
    Houston, TX
    Vehicle:
    91 Wrangler YJ
    2 inch body lift
    It's a 2" body lift, but whoever installed it put the blocks directly on the frame and both pieces of the bushing are on the bottom side of the frame. So, since I have to fix it and they look ruff I'm going to replace them at the same time. I'll go ahead and order them. I keep running across things that are not done right on this. I knew it was going to be a project which I don't mind. I have another truck I've been working on for about 8 years. This Jeep is going to be fun.

    I took a look at Creekside... It looks nice.
     
    vlkski, Feb 1, 2017
    #22
  3. Feb 1, 2017 at 4:31 PM
    #23
    OFFGRID

    #23
    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    It's not bad if you need a close by trail to test new mods on the jeep before hitting the big stuff.
     
    OFFGRID, Feb 1, 2017
    #23
Page 2 of 2
Register FREE to Reply!
To Top