1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Rocker arm

Discussion in 'Cherokee' started by Chelly, Feb 20, 2017.

  1. Feb 20, 2017 at 3:48 PM
    #1
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    I have a 2001 jeep cherokee limited, the rocker arm came off, we put it back on but it's loose, apparently from what I have read that is not good, how do I get it to not be loose and moving?
     
  2. Feb 21, 2017 at 2:41 PM
    #2
    Jasons4.6

    Jasons4.6 Active Member

    Joined:
    Feb 19, 2017
    Member:
    #1003
    Messages:
    38
    Gender:
    Male
    First Name:
    Jason
    Vehicle:
    Black 97 cherokee sport
    4.6 stroker, m90 supercharger, true dual exhaust with sidepipes, old school 6 pack mopar hood scoop, and 3.55 gears front and rear
    Sorry to say but from what I see here is that you may have a bent push rod, bad lifter, and/or worn camshaft lobe.
     
  3. Feb 21, 2017 at 3:55 PM
    #3
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    This engine does not have push rods
     
  4. Feb 21, 2017 at 5:05 PM
    #4
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Could the lifter be stuck in the compressed position? Maybe sludge?
     
  5. Feb 21, 2017 at 5:16 PM
    #5
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    It's brand new
     
  6. Feb 21, 2017 at 5:23 PM
    #6
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    The universal tool ( valve spring compressor) that was used to put it in does not work for the 2001 jeep v8 , we just put it in our self with out the tool.
     
  7. Feb 21, 2017 at 6:47 PM
    #7
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Are you hearing rocker arm/lifter chatter when the engine is running? I'm assuming you are feeling it being loose when the motor is not running. Did you just replace the one lifter or all of them. How many miles on the motor and has it been rebuilt.
     
  8. Feb 22, 2017 at 9:00 AM
    #8
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
     
  9. Feb 22, 2017 at 9:04 AM
    #9
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    Yes it makes a noise, we seen the rocker arm laying there, and yes we are feeling it loose when the motor is not running, motor has not been rebuilt but I have put a lot of new parts on it, it was taken out and put back in.
     
  10. Feb 22, 2017 at 9:44 AM
    #10
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    My opinion is one of 2 things. You have something blocking the oil channel under the tappet, or more likely you have a flat lobe and need a new cam.
     
  11. Feb 22, 2017 at 9:56 AM
    #11
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    Just one lifter was replaced.
     
  12. Feb 22, 2017 at 10:17 AM
    #12
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    You have 12 Lifters with 12 lobes of the cam under them. If that 1 lifter is not lifting there is either no oil flow to expand the lifter, or the lobe itself is flat. If the lobe is flat you have to 1) have a lobe made and a machine shop press off the bad lobe and then press them all back on at the right degree (not worth the expense) or 2) order a Competition towing cam (for more low end torque) and replace it the existing cam.
     
  13. Feb 22, 2017 at 6:29 PM
    #13
    Chelly

    Chelly [OP] Member

    Joined:
    Feb 20, 2017
    Member:
    #1009
    Messages:
    8
    Gender:
    Female
    Vehicle:
    2001 grand jeep cherokee limited v8
    Thanks for all the advice, I got my boyfriend on it :)
     
  14. May 22, 2017 at 4:18 AM
    #14
    jimh142

    jimh142 New Member

    Joined:
    May 22, 2017
    Member:
    #1486
    Messages:
    4
    Gender:
    Male
    First Name:
    jim
    Vehicle:
    03 ram 4.7
    rockerlocks
    if you havn't started your motor the rocker arm will more than likely be loose until you start it & get oil pumped up to it.But if your rocker arm fell off you should install rockerlocks or it will happen again. Go to rockerlocks.com for more info.That's if it is a 4.7 i'm assuming.
     
  15. Sep 2, 2017 at 7:28 PM
    #15
    jimh142

    jimh142 New Member

    Joined:
    May 22, 2017
    Member:
    #1486
    Messages:
    4
    Gender:
    Male
    First Name:
    jim
    Vehicle:
    03 ram 4.7
    rockerlocks
    your lifter or slack adjuster as they call them now, is collapsed or stuck. you can replace the slack adjuster but if that's all you do your rocker will fall off again probably soon.get a new slack adjuster & go to rockerlocks.com & order a set of rockerlocks you will never have a problem again.these work on 3.7&4.7 motors.
     
  16. Sep 2, 2017 at 8:02 PM
    #16
    JKBob 25

    JKBob 25 Well-Known Member

    Joined:
    Mar 22, 2017
    Member:
    #1197
    Messages:
    3,895
    Gender:
    Male
    First Name:
    Bob
    Jersey Shore, NJ
    Vehicle:
    2016 JK Wrangler Sport
    4 months. And nothing from the OP. Really. At least post your fix. What you did to fix it. Don't just blow us off. We tried to help. At least let us know what the issue was. Peace out.
     
  17. Sep 4, 2017 at 12:01 PM
    #17
    jimh142

    jimh142 New Member

    Joined:
    May 22, 2017
    Member:
    #1486
    Messages:
    4
    Gender:
    Male
    First Name:
    jim
    Vehicle:
    03 ram 4.7
    rockerlocks
    the fix was in my post go to rocker
    i did give you a fix in my post before go to rockerlocks.com.
    rocker locks are a spring clip designed to hold the rocker arms in place on the dodge ram & jeep 4.7 V8 and the 3.7 V6 [all years all models] to alleviate the problem of falling rockers.this is a non moving part it just sits there & holds the rocker in place probably will never wear out.
    I had this problem with my 03 ram 4.7 & found out [no one had a fix] so i set out to find one & i did, i designed a spring clip & put it on the 2 rockers [that fell off 3 times in 3 weeks] I have had no problem since, after about 4 months & 5000 miles later.these really work.call for more info
    jim 816-274-2730 [update] it's now been about 6 months & around 8000 thousand miles still no problems.Call me i now have my patent and am ready to sell let me help you save your truck as i did mine Without these rockerlocks my truck was junk they saved my truck that i love.price is $15.00 ea or $12.00 ea in a set of 12 for 3.7v6 or 16 for 4.7v8.Thats only $144.00 or $192.00 a set pretty low price to pay to save your beautiful truck if you ask me.it cost me much more developing these for my truck & worth every penny.call today be back on the road in no time.jim 816 -274-2730. or leave message in email thanks.rocker arms or slack adjusters not included rockerlocks only but spacer washers are included.[We are the only ones on the planet that have these. rockerlocks.com.

    We have now sold many sets with no complaints! This tells me they are working great for everyone.WE are sure these will fix your problem of rocker arms falling we are giving a 30 day warranty if you have any problem with rockers falling off within this time simply send them back for a full refund minus shipping & handling.
     
    Offroad798, aggrex and chris4x4 like this.
  18. Sep 4, 2017 at 1:34 PM
    #18
    JKBob 25

    JKBob 25 Well-Known Member

    Joined:
    Mar 22, 2017
    Member:
    #1197
    Messages:
    3,895
    Gender:
    Male
    First Name:
    Bob
    Jersey Shore, NJ
    Vehicle:
    2016 JK Wrangler Sport
    Sorry man. I misread your post. My bad. Sorry.
     
  19. Feb 15, 2018 at 3:14 AM
    #19
    jimh142

    jimh142 New Member

    Joined:
    May 22, 2017
    Member:
    #1486
    Messages:
    4
    Gender:
    Male
    First Name:
    jim
    Vehicle:
    03 ram 4.7
    rockerlocks
     
  20. Feb 15, 2018 at 9:52 AM
    #20
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    @jimh142 Earlier I believe @JKBob 25 was referring to the OP or original poster when he asked what did you do to fix your issue, not you when you are posting a fix. We haven't heard back from Chelly on what she did to fix her problem. It is nice to know so that other people can come on here and find a fix for their problem. Your rockerlockers sound like a good fix and I will keep them in mind if I ever run accross this issue.
     
    JKBob 25 likes this.
To Top