1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

2000 Grand Cherokee AC vent issue

Discussion in 'Grand Cherokee' started by mcf57, Jul 7, 2020.

  1. Jul 7, 2020 at 3:54 PM
    #1
    mcf57

    mcf57 [OP] New Member

    Joined:
    Jul 7, 2020
    Member:
    #4832
    Messages:
    2
    Gender:
    Male
    First Name:
    Mitch
    Vehicle:
    2000 Jeep Grand Cherokee
    We have a 2000 Grand Cherokee. All seems to be working except a slight issue with the AC. It kicks out perfectly cold air but will ONLY blow it out through the front windshield defrost vents. No matter what area setting you try to change it to (feet, front, feet/front, defrost/feet), it always just keep blowing out on the windshield..

    Any ideas what is going on here? Is this something I could maybe attempt to fix? I have replaced the stereo so have some technical experience, but not sure if this is something easy or hard (requiring taking apart whole dash)
     
    Last edited: Jul 7, 2020
  2. Jul 7, 2020 at 5:43 PM
    #2
    Jim Beam

    Jim Beam Well-Known Member

    Joined:
    Feb 11, 2019
    Member:
    #2891
    Messages:
    596
    Gender:
    Male
    First Name:
    Donald
    Vehicle:
    1986 CJ7
    Fuel Injection, Dana 44s, T18, 4.10s w/lockers
    I had that same issue on my '99 Dodge Ram. It was a hardened and broken vacuum line that controls the vents. The line was broken near where the vacuum line goes into the firewall in the engine compartment. I used a length of heat shrink tubing to repair it. It also could be a broken line closer to the vent controller under the dash. Good luck!
     
  3. Jul 9, 2020 at 8:48 PM
    #3
    mcf57

    mcf57 [OP] New Member

    Joined:
    Jul 7, 2020
    Member:
    #4832
    Messages:
    2
    Gender:
    Male
    First Name:
    Mitch
    Vehicle:
    2000 Jeep Grand Cherokee
    I figured it out. Sounds about the same. I watched some youtube videos and one guy showed a hose that simply came off in the engine area and near the firewall. Sure enough, I had the same issue. Applied the hose back on to the connection and all was good. While I didn't do this, I wonder if I should glue it on somehow to avoid it falling off again. Or will this not be good and possibly damage it?

    Here is what was basically wrong: https://youtu.be/OFhW2GjjVxE
     
  4. Jul 10, 2020 at 4:56 AM
    #4
    aggrex

    aggrex Well-Known Member

    Joined:
    Sep 12, 2016
    Member:
    #203
    Messages:
    4,912
    DE
    Vehicle:
    Backcountry '16
    Tuffy>AEV>TTO>JW>STech>EVOcage>MagnaFlow>SpiderTrax>RockHard>TF>SpringTail>67design>Bolt>GPCA>Curt>
    Good job figuring that out. Do not glue that hose back on. Either get a new hose or use a small hose clamp or if there is excess hose cut an inch off for a tighter fit.
     
    JKBob 25 and LYFZGOOD like this.
  5. Jul 10, 2020 at 9:50 AM
    #5
    LYFZGOOD

    LYFZGOOD members

    Joined:
    Jul 22, 2017
    Member:
    #1701
    Messages:
    983
    Gender:
    Male
    Wv
    Vehicle:
    1998 Jeep Wrangler Sahara
    2.5” lift 32x11.50x15,cold air intake, Smittybuilt stainless steel Bumpers, rough county pocket flares,Rugged ridge seat covers and floor mats. Conversion LED headlights 20’ LED Light bar hardtop,soft top,bikini top.
    It’s not a high pressure hose, a wire tie would be sufficient
     
    aggrex likes this.
  6. Jun 27, 2022 at 4:49 PM
    #6
    jwein87162

    jwein87162 New Member

    Joined:
    Jun 27, 2022
    Member:
    #6575
    Messages:
    1
    Gender:
    Male
    Hey Thanks . . this worked for me . . . Great video showing where & how. . Thanks again
     
To Top